curve selection

Rank: 2

chris

Assistant Engineer

posts: 43

Registered: 2011-5-24

Message 1 of 6

 curve selection
23-03-2013 09:55 . pm | View his/her posts only
I cannot select curves on a drawing in CAM, I use this to program a wire edm What is happening in 2013?

Rank: 1

Mirko

Newbie

posts: 215

Registered: 2011-11-23

Message 2 of 6

24-03-2013 04:59 . am | View his/her posts only
hi
Good question!
This is a beta beautiful and good, i can't understand us here we feel pulled in lap! The money is good, the software no!


We are wondering if the answer is that it solves sp1 in a few month or if you will adjust immediately! Reports also made too many , complaints with dealer , lost time bringing confidence we have lost count. When we have serious answers and concrete? When I say to my customers that will improve and then not happens , i then miss esteem and credibility.


We have purchased a new license premium on trust but also that a disaster, the 2.5d it is prehistoric and innutile in production, and the 3D produces tool paths little performer for the tools of the day d' today, I have seen better products that should be more poor. The impression it is a total lack of any real development , all without offenses but disappointments are always more, we remain confident even if doubts now. (babylon traslator)


Mirko

Rank: 1

ZW3DUser

Newbie

posts: 51

Registered: 2013-2-8

Message 3 of 6

26-03-2013 03:51 . am | View his/her posts only
You can not compare ZW3D with TopSolid !
Dont compare only the functions, compare also the price.
TopSolid is 3x expensive like ZW3D.

Rank: 2

chris

Assistant Engineer

posts: 43

Registered: 2011-5-24

Message 4 of 6

26-03-2013 05:25 . am | View his/her posts only
I see this thread has been hijacked. The thread is about ZW failing to allow the selection of curves off of a drawing. Personally I do not want automatic selection. I can read and write G code and have been doing it for 40 years. I program not only milling machines but wire and laser. All the programing I do is for 1 of a kind no production. Wire and laser require different cutting schemes then do mills. older milling machines like found in many small shops cannot function with the aggressive feeds and speeds that some automatic programs generate.
That being said. My original concern is that I cannot select lines and curves from a drawing in 2013. 2012 was no problem.

Rank: 1

cutter

Newbie

posts: 55

Registered: 2011-11-23

Message 5 of 6

26-03-2013 10:32 . am | View his/her posts only
Before you believe Jon ask him for a file done in ZW. He is not a user, has never been a user and A, if you send him a file he can't work on it and B, if you ask him to produce a file to support his comments you will only get evasions. If you guys as posters here and at ZW can't figure out that Jon is a fraud you deserve to have your time consumed by him. Google JonBanquer and see for yourself the trail of bread crumbs that follow him that he can't censor or remove. A good place to start to would be Novedge where you can go to the interview section and see Jon Banquer listed under interviews as "Jon Banquer, Cad Troll" and find out a bit about him there.
http://groups.google.com/group/c ... acb5f?q=jon+banquer

http://www.cnczone.com/forums/pr ... e_under_attack.html

http://grabcad.com/jon.banquer

http://www.mastercamforum.com/viewtopic.php?f=8&t=10

http://www.slideshare.net/JonBanquer

https://groups.google.com/forum/ ... idworks/VcVjdvqN2Cc

https://groups.google.com/forum/ ... idworks/3H8Oe691eyI

Rank: 1

Jon

Newbie

posts: 61

Registered: 2009-12-31

Message 6 of 6

26-03-2013 11:01 . am | View his/her posts only
Post Last Edit by JonBanquer at 2013-3-26 11:16

Please remove cutter/Dave Ault's lies and personal attacks that litter this forum. cutter/Dave Ault has done nothing but trash ZWSOFT and ZW3D all over the Internet for at least the last year. cutter/Dave Ault claims he's given up on ZW3D and is raffling off his ZW3D dongle for free. This can be confirmed by reading his worthless fog blog:

http://solidedging.wordpress.com ... -zw3d-buyer-beware/

It's time to remove a loser and a liar like cutter/Dave Ault from this forum as he has nothing positive to offer and has done everything possible to try and make ZW3D and ZWSOFT fail.

I still occasionally use my seat of VX 10 that I have owned for many years now. When I feel the CAM portion of ZW3D is ready for production machining, I will upgrade via Bob Fischer but not until them.

Both cutter/Dave Ault and Tim Markoski (posting in the link below as Keyser Söze)have done irreparable harm to ZWSOFT and ZW3D and should be banned from this forum for their actions and attempts to destroy ZWSOFT and ZW3D.

http://solidedging.wordpress.com ... ews-for-zw3d-users/

Anyone looking for an unbiased look at what I am all about can find it here:

http://cadinsider.typepad.com/my ... lid-edge-again.html



Jon Banquer
CADCAM Technology Leaders group on LinkedIn
See also