CAD software discussion forum > CAD Tutorial & Tips > how to draw ellipse in engineering drawing

# how to draw ellipse in engineering drawing

how to draw ellipse in engineering drawing

06-12-2013 10:12 . am | View his/her posts only

**How to draw ellipse in engineering drawing**?

Thanks for any answer.

06-12-2013 10:14 . am | View his/her posts only

Step-1 Draw a horizontal axis of some suitable length. And mark a point O on it.

Step-2 Draw a vertical axis, perpendicular to the horizontal axis & passing through the point O of the length equal to the length of minor axis, which is 60 mm and give points C & D as shown into the figure.

Step-3 Mark the points F1 & F2 Which are focal points on the horizontal axis and are 80 mm apart from each other.

Step-4 Measure the distance between the point F1 & C or D and with this distance keep O as center and cut the horizontal axis on both the sides and give points A & B, which is the major axis of the ellipse. Hence the distance of the major axis is 100 mm.

Step-5 With O as center and radii equal to OC and OA or OD and OB draw two circles.

Step-6 Divide these circles into 12 equal divisions as shown into the figure. And give the notations 1,2,3, etc. where these lines of divisions intersect the outer circle & 1’,2’,3’ etc. where these lines intersect the inner circle.

Step-7 Draw vertical lines from the points 2,3,5,6, in downward directions and 8,9,11,12 in upward directions respectively.

Step-8 Draw horizontal lines from the points 2’,3’,11’,12’ in left hand direction and from the points 5’,6’,8’,9’ in right hand direction respectively.

Step-9 Give the notations p1,p2,p3 etc. at the points of intersections of these horizontal & vertical lines respectively as shown into the figure.

Step-10 Draw a smooth free hand medium dark curve from the points p1,p2,p3 etc. in sequence, so the resulting curve is the ellipse.

Step-11 Give the dimensions by any one method of dimensions and give the name of the components by leader lines wherever necessary.

Step-2 Draw a vertical axis, perpendicular to the horizontal axis & passing through the point O of the length equal to the length of minor axis, which is 60 mm and give points C & D as shown into the figure.

Step-3 Mark the points F1 & F2 Which are focal points on the horizontal axis and are 80 mm apart from each other.

Step-4 Measure the distance between the point F1 & C or D and with this distance keep O as center and cut the horizontal axis on both the sides and give points A & B, which is the major axis of the ellipse. Hence the distance of the major axis is 100 mm.

Step-5 With O as center and radii equal to OC and OA or OD and OB draw two circles.

Step-6 Divide these circles into 12 equal divisions as shown into the figure. And give the notations 1,2,3, etc. where these lines of divisions intersect the outer circle & 1’,2’,3’ etc. where these lines intersect the inner circle.

Step-7 Draw vertical lines from the points 2,3,5,6, in downward directions and 8,9,11,12 in upward directions respectively.

Step-8 Draw horizontal lines from the points 2’,3’,11’,12’ in left hand direction and from the points 5’,6’,8’,9’ in right hand direction respectively.

Step-9 Give the notations p1,p2,p3 etc. at the points of intersections of these horizontal & vertical lines respectively as shown into the figure.

Step-10 Draw a smooth free hand medium dark curve from the points p1,p2,p3 etc. in sequence, so the resulting curve is the ellipse.

Step-11 Give the dimensions by any one method of dimensions and give the name of the components by leader lines wherever necessary.

17-02-2014 06:41 . pm | View his/her posts only

Wow, that looks like a lot of work

See also

- 3d modelling programs
- autocad automatic saving command
- How to print a multi-page PDF from drawings
- zwcad portable
- 3d home design dwg files
- drawing a parabola in autocad
- free 3d cad software dwg
- 3d cad software
- buy solidworks 2009
- copyclip command not allowed during reference editing
- autocad commands
- how to open dwg files in autocad
- How to Create Region in AutoCAD
- how to convert text to mtext in autocad
- set autosave in autocad