Message 1 of 14
I want to mill 4 parts with 4 axis.
All parts are the same, so i want to drill part 1 rotate, drill part 2, rotate...
Then i want mill part 1, rotate, mill part 2...and so on.
For this i want use offset like G54,G55,G56... for each part.
But here is a problem. I made many changes on the machine settings, with muliti axis, i set a "A" axis in the configuration of the machine.
For this i want to use the offsets from each operation, not the machine.
N23 G55 G90 G00 X-25.9795 Y125.7118 Z65.7095 A-90.
For this position i use the plane with G55, but this point must be X0, Y0, Z0 not like this.
This is because i can only use the machine output, not operation otherwise i get an error.
On the machine i want to adjust the positions of each part, so i want use G54,G55...and i want this offsets in the middle of the part.
Is there a way to solve this ? Or is this the wrong way to mill multi parts on a 4 axis ???
I use : ZW3d 2012 SP2
Message 2 of 14
Message 3 of 14
As Sam is out of the office, I couldn't get your email or skype from him, could you please send me a quick message via skype(colin_chuang2008), and then I can contact my local reseller to provide a quick support.
Message 4 of 14
Message 5 of 14
Message 6 of 14
Message 7 of 14
I see your file and this will work. I use this also before to mill parts.
The Problem here is to use a 4. axis and the offsets.
I think in ZW3D 2012 there is no way to use this.
With ZW3D2013 and ZW3D2014 Tony write me it will be makeable...i write back if i know more.
Thanks for your sample !
Message 8 of 14
With ZW3D2014 and a "little" changing of the post processor it will be makable.
At the moment im a little angry, because ZW3D and encee wrote about a "new" HURCO post processor.
The 4 axis is full supported about HURCO, so i get a full 3D simulation on the machine !
It is not a "super option" ore something.
In ZW3D the are 4x HURCO PP's but they dont work.
So ZW3D please rename this to:
"HURCO 4x not work correct unlike you make some changes_PP"
From encee the german reseller i get the last answere about 11.06.2014 : "The people you wrote about, is tot in the office at the moment"
So why i should write them back ? Why i should upgrade to ZW3D2014 ?
The "selfmade" SG post processor newer worked correct with the older HURCO machines, that use BNC instead of industry nc (fanuc standard). So i must have lifetime support !
Nice day to all !
Message 9 of 14
I understood your concern about the upgrade, and thanks for your continuous trust. Tony did the best to test it with the similar machine to assure that ZW3D 2014 is working according to your specified description.
I hope you can spend some time in reading the new features of ZW3D 2014 or ZW3D 2013 (http://www.zwsoft.com/zw3d/2014/), comparing to ZW3D 2012, besides easier and faster post processor, the tool path editor helps to increase programming interface a lot, the multiple-thread computing increases the calculation time a lot, etc. The upgrade would definitely increase the machining efficiency.
Message 10 of 14
I am involved is supporting ZW3D here simply because I can. It is not my core business. However there is a limit to how far back software can be supported - especially when BIG improvements are being made on a regular basis.
So whilst I know it costs to keep current - ultimately that is the only way you can reasonably expect to be have lifetime support.
If we expend capital on a machine we devalue it annually because it is wearing out. When you replace the machine you sell the only one fr scrap and expect lot more from the new.
CADCAM software is being made newer annually and is not destined for the scrap heap IF you keep it current. no one questions that.
People paint themselves into a corner by NOT upgrading.
ZW3D is as one of the more reasonable annual upgrade CADCAM costs on account of the relatively low initial price.
Best idea I have seen is for you to put aside the annual upgrade - perhaps starting 4 months or earlier before new release and put 25% away each month... then when it is released you can start the transition and enjoy all the benefits for the maximum time.
Message 11 of 14
The "lifetime support" was a joke !
I understand it, what i want is not makeable with ZW3D 2012.
In the past we have a lot of problems with a postprocessor (not ZW3D included) and for HURCO this is newer running. Also i write many emails to the support, and many times they say "you are the first with this problem". Problems i know are spiralcut and restmill, solved in 2013 and 2014 !
I report the restmill problem here, and then it will fixed ! Same with spiralcut ! (search the forum for that)
But i think, it is the job of a support to contact ZW3D, not nine.
And thats the thing i mean "they" must give me a lifetime support for all the problems.
Hope this solve my mistake :-)
Message 12 of 14
Honestly - I figured you were being 'easy' with words.
The problem you have with the reseller is something hard to fix maybe.
Your comments highlights a very good thing about ZW - that you can indeed get right back to the factory id the normal route fails. Some software users don't have that option - it is very hard to be heard.
In the past I have probably tied up one employee with bugs and improvement recommendations. Things are much better now.
When will you be using 2014?
Message 13 of 14
Message 14 of 14
I don't think so.
And i do not need any rotation ! I turn the 4 axis, but it will be G17 anytime.
Thats the problem, ZW3D change it to G18 and G19.
And i dont want to edit the nc code !
I want a output and this output must work without changing.
This part i programm on the HURCO dialog without problems, because the 4. axis is full integratet.
ZW3D 2012 can not do this on a HURCO 4x.
5x drilling will will not work like they say. Of corse, it could be that it will work with other maschines...i dont know. With 2014 and a "smal changing" of PP it will be makable...they say.
In ZW3D youtube vids are told this is so easy...klick to 5x and they will drill with rotation.
Anyone here use this ?
Ok, HURCO is a little other maschine...but if they say, "NEW HURCO PP" it must work.
But before we buy any update i will test it by myslf. I will output a nc code and this must be run out of the box. This time i will see the result first! As we order 2012 there are to many problems with PP. Before we buy "they" say always, its no problem...the we buy and we see the problem !
Let the time see what we do or not
- AutoCAD Installation Error 1603
- drawing a gear in autocad
- zwcad 2009
- mechanical engineering software free download
- sheet metal design tips
- zwcad price in india
- free dwf viewer for mac
- autocad 2012 product key
- cad 3d models download
- autocad automatic saving command
- 3D Software Download
- how to convert text to mtext in autocad
- DXF converter
- mechanical design software free download
- how to import autocad file into sketchup 2013