CAD/CAM discussion forum > CAD > nest Xref does not display after xclicp in ZWCAD

nest Xref does not display after xclicp in ZWCAD

    
  Subscribe Topic

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 1 of 18

 nest Xref does not display after xclicp in ZWCAD
09-07-2014 04:11 . pm   |   View his/her posts only
Post Last Edit by Jenny_ZWCAD at 2014-7-29 08:46

Why is this X-Ref is not displayed (see picture)???Please change quickly as possible
reinstellen or a solution?????

Warum wird diese X-Ref nicht angezeigt (Siehe Bild) ???????

Bitte schnell als möglich ändern
oder eine Lösung reinstellen ??????????????

Bild 1.png
2014-7-9 17:18
Bild 2.png
2014-7-9 17:18

Rank: 5Rank: 5

Jan Pajerchin

ZWCAD Reseller

posts: 84

Registered: 2011-5-21

Message 2 of 18

10-07-2014 09:17 . pm   |   View his/her posts only
Perhaps it could be caused because you have older ZWCAD and newer AutoCAD and Xref DWG is in newer format which is not possible to read in old ZWCAD.

...If you want better answer - write you CAD versions, and check Xref DWG version...

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 3 of 18

10-07-2014 09:24 . pm   |   View his/her posts only
Autocad 2015

ZWCAD+ 2014 Pro

Rank: 5Rank: 5

Jan Pajerchin

ZWCAD Reseller

posts: 84

Registered: 2011-5-21

Message 4 of 18

10-07-2014 10:19 . pm   |   View his/her posts only
Hmm.
Fitsr of all - have you tried directly to open this XRef as standard DWG drawing in ZWCAD ?

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 5 of 18

10-07-2014 10:24 . pm   |   View his/her posts only
in Create Clipping the fault (see picture)

in Create Clipping liegt der Fehler (siehe Bild)

Bild 1.png
2014-7-10 22:24

Rank: 5Rank: 5

Jan Pajerchin

ZWCAD Reseller

posts: 84

Registered: 2011-5-21

Message 6 of 18

10-07-2014 11:18 . pm   |   View his/her posts only
I'm asking if - after you open in ZWCAD the file:
aaa.jpg
2014-7-10 23:18

You see everything correctly.

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 7 of 18

11-07-2014 12:30 . am   |   View his/her posts only
Yes

Alles ok

Rank: 5Rank: 5

Jan Pajerchin

ZWCAD Reseller

posts: 84

Registered: 2011-5-21

Message 8 of 18

11-07-2014 06:12 . pm   |   View his/her posts only
Sure you understand that to detect the source of your problem without testiog of your drawing is a bit time consuming...

I suggest now to test, if you will see everything correct if you attach the file
aaa.jpg
2014-7-11 18:09

as Xref to a new "blank" DWG file.

If it displays correctly - we will know (nearly for 100%) that the problem is directly in your original DWG.

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 9 of 18

15-07-2014 12:46 . pm   |   View his/her posts only
In a new drawing all open ok.

In einer neuen Zeichnung geöffnet alles ok.


Bild 1.png
2014-7-15 12:46

Rank: 5Rank: 5

Jan Pajerchin

ZWCAD Reseller

posts: 84

Registered: 2011-5-21

Message 10 of 18

15-07-2014 10:34 . pm   |   View his/her posts only
Great,

Now we know the problem is only in your original drawing with attached xref...

Only for to be sure:
I really expect you have all of the layers On & Thaw ...so I expect this problem will not be caused by Off or Frozen layer.
Is it OK ?

Try to _PURGE your drawing (if you didn't tried it yet)
and after that try to run _AUDIT command (if you didn't tried it yet)

I expect it will not help you ...but there is perhaps 1% chance it will help.

If it will not help you

Try to detach problematical Xref & attach it again (in your original drawing).
...there is 5% chance it will help

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 11 of 18

16-07-2014 12:34 . pm   |   View his/her posts only
I have now done everything as they have written
unfortunately no success

Ich habe jetzt alles so gemacht wie sie geschrieben haben
leider kein erfolg


Bild 1.png
2014-7-16 12:34

Rank: 5Rank: 5

Jan Pajerchin

ZWCAD Reseller

posts: 84

Registered: 2011-5-21

Message 12 of 18

16-07-2014 07:01 . pm   |   View his/her posts only
Hmm

1. Try to save your XREF DWG file in DWG 2013 format (your xref could be saved in older DWG format)
2. Test if such XREF is correctly displayed in your problematical DWG

If I remember rightly one customer had simillar problem (in past) and it helped him...

Otherwise I'm afraid there is no other chance - and it will be needed to test your DWG with your XREF on my side

You should to poublis here a link for download of your problematical DWG + your XREF (if it couldn't be published - reduce both files and delete most of their objects)

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 13 of 18

16-07-2014 08:49 . pm   |   View his/her posts only
Does not
I give up, we will work with Autocad on.



Hilft auch nicht
ich gebe auf, wir Arbeiten mit Autocad weiter.

Rank: 8Rank: 8

Jenny

Super Moderator

posts: 538

Registered: 2013-5-6

Message 14 of 18

17-07-2014 09:32 . am   |   View his/her posts only
hi Dober, could you attach your xref drawing and the original drawing to here and let me test the problem? If you have trouble to attach drawing to this forum, you could email to me wuqiaojuan@zwcad.com. Thank you in advance.

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 15 of 18

17-07-2014 12:48 . pm   |   View his/her posts only
I sent them an e-mail.

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 16 of 18

22-07-2014 01:24 . am   |   View his/her posts only
What is now with my drawing?
Have they checked the Zeichnng've been waiting for an answer

Was ist jetzt mit meiner Zeichnung ?
Habe sie die Zeichnng schon geprüft warte auf Antwort

Rank: 8Rank: 8

Jenny

Super Moderator

posts: 538

Registered: 2013-5-6

Message 17 of 18

23-07-2014 11:08 . am   |   View his/her posts only
Hi Dober,
Thank you for the drawings.
When the xref is inserted, everything shows well, the problem is, when we use XCLIP to clip the xref, the nest xref turn to be invisible. We will try to solve this problem as soon as possible. Sorry for the inconvenience.



(ID: 6795)

Rank: 3Rank: 3

Dober

Junior Engineer

posts: 131

Registered: 2011-9-22

Message 18 of 18

23-07-2014 03:58 . pm   |   View his/her posts only
Super Danke
See also
X